Clik here to view.
Bluetooth Multimeter
informative idea, after reading this i m thinking to use this Statistics : Posted by twobrain • on Mon Aug 12, 2013 1:04 pm • Replies 3 • Views 755
View ArticleBluetooth Multimeter
kburgess wrote:I have never been able to get the bluetooth meter I bought to work. Thought I would give it one more try, nope.I loaded (new?) software from wiki on Android. I can get the device to...
View ArticleBluetooth Multimeter
I have never been able to get the bluetooth meter I bought to work. Thought I would give it one more try, nope.I loaded (new?) software from wiki on Android. I can get the device to connect, at least...
View ArticleClik here to view.
Bluetooth Multimeter
Does anyone have the Bluetooth Multimeter working?Has anyone managed to download the software without problems? I can't unzip without errors on any of files.Is the meter already pre-programmed with the...
View ArticleClik here to view.
Arduino Yun + GPRS Shield v2
Hello all,I'm posting here because I can't get the http://www.seeedstudio.com/depot/GPRS-S ... Path=19_20 Seeedstudio GPRS Shield v2 to work with my Yun. I've seen the wiki page for the shield:...
View ArticleI can't change the amplitude of the signal generator
Do you mean you can't change the amplitude at all or you can't raise it above 3v?If the former then you need to say which firmware you are using.If the latter then that is the limit of the hardware....
View ArticleI can't change the amplitude of the signal generator
figured out how to change DS203 waveform generator, but can not increase the amplitude of the signal? it's about 3V, but I need moreStatistics : Posted by andybeg • on Thu Sep 18, 2014 1:49 pm •...
View ArticleSeeeduino GPRS
Hi there,I just recently bought a Seeeduino GPRS but sometimes work using USB port and VisualMicro (Leonardo Board Option).It is very unstable. Is it required to provide higher voltage thru Vin instead...
View ArticleCAN BUS Shield settings 4096 bod/s
From my calculations, you will need to change the crystal to 8 MHz to achieve this bit rate. The performance cost would be negligible since the bus speed is slow.Calculations: CFG1 = 3CCFG2 = F0CFG3 =...
View ArticleCAN BUS Shield settings 4096 bod/s
help me please.. CAN bus with speed 4096 bod/s (in sensors tower cranes)in shield library min speed 5kBPS#define MCP_16MHz_5kBPS_CFG1 (0x3F) - 00111111 -< CFG1 - this use speed? (in datasheet...
View ArticleCAN Shield Issue
It looks like someone tried implementing remote request frames and that got merged into the library... https://github.com/Seeed-Studio/CAN_BUS ... a9b22b0ca2As for the LEDs, that is probably because...
View ArticleCAN Shield Issue
HelloI am using a v1.0 CAN SHIELD attached to a UNO R3using IDE 1.0.5, I have uploaded the receive_check program which compiles and uploads correctly. I don't have any other device to read the CAN off...
View ArticleLonger Grove cables give large number of IO Errors
Use shielded cables and connect the shield drain wire at one end (the end closest the the microcontroller would be best) to a good Earth ground.Statistics : Posted by robert.e.shelton • on Fri Aug 22,...
View ArticleLonger Grove cables give large number of IO Errors
My project involves sensors located at different places inside a small building, and other sensors located outside. A few sensors will be mounted near the RasPi / GrovePi control unit, but most need to...
View ArticleEthernet shield constant reset status
This is new to me. I have three Ethernet shields: the Official Arduino R3 Ethernet Shield with PoE module populated, the Freetronics Ethernet Shield, and the Seeed Studio Ethernet Shield V1.1 I picked...
View ArticleEthernet shield constant reset status
Hi, recently picked up an ethernet shield for my Arduino Uno R3. However... anytime I plug in an ethernet cable, theunit immediately goes into reset (red light comes on.) The device does not show up as...
View ArticleArduino mega 2560 and NFC shield V.2 Didn't find PN53x board
Woops! too big image! I'f you want to see it fully, press ctrl - until you got better view. But, i'll repost the smaller image if necessaryStatistics : Posted by benedicta_stella • on Fri Sep 19, 2014...
View ArticleClik here to view.
Arduino mega 2560 and NFC shield V.2 Didn't find PN53x board
Hey, allI want to try the "readMifareTarget ID.ino" using arduino atmega 2560 and Seeedstudio NFC shield v.2. I got the library and the example from the following link:...
View Articlecan't get to pins 8,9,10 with SD shield on Uno R3
Hi I need to use output pins 8 9 and 10, with the the SD shield mounted on my UNO R3, but these pins do not respond to input or output with the shield in place. They work fine with the shield off. The...
View ArticleAny chance of reviving the DSO201?
You have to be more specific about which version of the Nano you are talking about. There are many. What 2GB memory card?Statistics : Posted by jsarment2 • on Sun Sep 14, 2014 6:04 am • Replies 3 •...
View Article