BenF 3.x FW on new LCD driver devices [flick. screen solved]
palindrom wrote:I have a source code for 4.22 original firmware which handles ILI 9341 display so it should be possible to run BenF 3.64 on new devices.Is this something you can share? Is it available...
View ArticleBenF 3.x FW on new LCD driver devices [flick. screen solved]
[EDIT 2]rimidalv007 patched BenF 3.64 APP + 3.53 LIB and it can now operate on ILI9341-equipped devices.Direct link to the post with attached firmware:viewtopic.php?p=18556#p18556[/EDIT][EDIT]Thanks to...
View ArticleCan bus shield and Arduino Uno pins
I have a good working CAN bus shield on the Arduino-Uno, but not anymore if the Arduino is serving a Adafruit VS1053 musicplayer on the SPI bus as well . According to my request to Adafruit, it could...
View ArticleCan bus shield and Arduino Uno pins
CAN-bus shield communicates with Arduino through SPI interface, so pin 13, 12, 11, 10 and 2 are occupied. Other pins on Arduino you can still use.Statistics : Posted by anton.i.belov • on Tue Apr 15,...
View ArticleCan bus shield and Arduino Uno pins
May be I understand something wrong but I can't find any information about the communication between Arduino and the CAN-shield. Can I stil use all pins from Arduino Uno (through stackable headers) or...
View ArticleThe PCB weight is too damn high!
I am happy to confirm that Seeedstudio now have adjusted their PCB shipping fees. Special thanks to Fusion PCB manager Raymond who followed up on my requests!These numbers are from my own buying...
View ArticleThe PCB weight is too damn high!
Hi there,i have adjusted the weight already. but please do understand that there are still tolerance there. for example, your board size is 3*3 cm, but the weight we still charge the 5*5cm because so...
View ArticleThe PCB weight is too damn high!
Hello, guys!Are you going to resolve this problem (incorrect weight estimation)?Your price and quality are good, but incorrect weight estimation causes too high shipping cost.For 10 pcs 5x5 PCB real...
View ArticleClik here to view.
The PCB weight is too damn high!
not solved yet Statistics : Posted by tannek • on Fri Oct 11, 2013 5:48 am • Replies 5 • Views 2872
View ArticleThe PCB weight is too damn high!
thank you so much for bringing this information to us! i will check the problem immediately.Statistics : Posted by tannek • on Fri Oct 11, 2013 5:48 am • Replies 5 • Views 2872
View ArticleThe PCB weight is too damn high!
For example the estimated weight for 10pcs of 2layer, 10cm x 10cm, 1.6mm FR4 are specified with 970g.Thats sounds a little too much for me .. so I've done some research and found an online...
View ArticleFarewell Seeed
I have had a Nano 3 for over 2 years I think,I wanted to use it for Auto Engine tuning and troubleshooting seemed to be just the thing ,small ,and portable,I bought 10x,100x attenuators,working on a...
View ArticleCan bus shield and Arduino Uno pins
sharp observation Jacket; I didn't see that wire.After cutting the small wire, the ohmic resistance between the two pads is infinite (out os scope of my little multi meter) (can that be?), but the...
View ArticleClik here to view.
Can bus shield and Arduino Uno pins
Hi , i have not used Adafruit MP3 player, so i may not show more useful suggestion to you, but one point you may have a attention.Just cut off the copper wire between CS and digital 10 via a knife, so...
View ArticleClik here to view.
Can bus shield and Arduino Uno pins
Thank you for the suggestions Jacket and Cory. I have now tried (unsuccessfully) the following and tested them separately in subsequent order :(1) Make connection between Pin 9 and CS. As in...
View ArticleClik here to view.
Can bus shield and Arduino Uno pins
pauldevissers wrote:thank you jacket, I will do this tomorrow:and will try it out without (1) library-modification and (2) worrying about Arduino-Uno using pin 9 for RESET. (OK?)paulp.s. for me it is...
View ArticleCan bus shield and Arduino Uno pins
If you use the version of the library I've been debugging and improving, it will allow you to define the CS pin for the CAN shield.Available here: https://github.com/coryjfowler/MCP2515_libStatistics :...
View ArticleClik here to view.
Can bus shield and Arduino Uno pins
thank you jacket, I will do this tomorrow:and will try it out without (1) library-modification and (2) worrying about Arduino-Uno using pin 9 for RESET. (OK?)paulp.s. for me it is not necessary to...
View ArticleCan bus shield and Arduino Uno pins
pauldevissers wrote:I have a good working CAN bus shield on the Arduino-Uno, but not anymore if the Arduino is serving a Adafruit VS1053 musicplayer on the SPI bus as well . According to my request to...
View ArticleNFC Shield V2 and NTAG's
I have a similar problem.I have tags that are verified on my cell phone NFC reader to be NXP MIFARE Ultralight NTAG203.The Arduino / NFC shield example sketch 'ReadTag' can read them, but, it says they...
View Article