Clik here to view.
Wifi Shield (Fi250) Function's button
Hi, i got stuck with function's button.I try to change mode this Wifi shield to AP Mode, in the instruction they said push it once for AP mode.but when i try to push that button nothing happenWifi led...
View ArticleHow to order boards with 70 um thick copper?
??Statistics : Posted by va26 • on Thu May 15, 2014 7:23 pm • Replies 0 • Views 30
View Articlebluetooth shield not working on a different baud rate
What happens after you upload the sketch?I can't write on bluetooth serial. After upload the sketch, leds of shield blink green/red but after 3 seconds the module doesn't work and leds don't...
View ArticleClik here to view.
bluetooth shield not working on a different baud rate
HiI am trying to have a faster way of logging the data captured from Uno through a Seeeduino BT shield.I gathered from the following website that it is quite possible with the Newsoftserial library,...
View Articlebluetooth shield not working on a different baud rate
if I change the baud rate from 38400, then after uploading the sketch, it doesnt go back to discovery mode again, so only green led continues to blink..Statistics : Posted by subrat.sahoo • on Thu May...
View ArticleRelay Shield V2.0
Hi, I just bought the seeeduino relay shield v2.0 and on the wiki page i found this note "do not operate more than 35v DC" since i couldn't find a proper specs, can anyone kindly explain if it is...
View ArticleHow to use the 9V Battery Clip with Grove?
Hithis is probably an easy one, so I'll start with "How to use the 9V Battery Clip with Grove?"I get the new Grove Starter Kit Plus, but the 9V Battery Clip doesn't make sense, the connector is not the...
View Articlenew to quad , Vp-p values wrong
hello guys .just bought the quad , was using nano before .fw is 2.72 i tested with built in square wave , when i change the voltage division ,for some reason the peak to peak voltage values also change...
View ArticleRelay Shield v2.0 is dead?
Hi all,I don't consider myself an expert in the matter but I find it hard to believe that I cannot get this Relay Shield 2.0 to work at all. While browsing this forum and others I found out that most...
View ArticleClik here to view.
How use "Grove - OLED Display 128*64" on Raspberry pi?
I am try to use "Grove - OLED Display 128*64" on my Raspberry pi.And my connection is in attach.And my source is from:|||||...
View ArticleEthernet Shield V1.1 Pin 10
I'm trying to get an Ethernet Shield v1.1, an SD shield, and a Touch Shield v1.0 all working together on my Mega. I have modified the SD shield and broken pins 10-13 out to a header that plugs into...
View Articleupdate DFU
Thank you for your answer bobtidey.Finaly I found a computer (windows 7 x64) capable to flash firmwares: the last official SYS1.61/APP1.11 (found on the minidso website) + gabonator + pawn.Statistics :...
View Articleupdate DFU
As far as I know the DFU is based on the standard SDK version but is modified to add specific features. I doubt whether the standard one would work, but I haven't tried that. I have never been able to...
View Articleupdate DFU
I found some answer.To upgrade the DFU I need to use the ISP interface (CN7).So the remaining questions are:* DFU V3.13C is it the last version? If no where to find the last one?* Where to find the...
View Articleupdate DFU
Hi,I just receive my DSO Quad (Hardware 2.72, SYS 1.60, APP Plus A1 V1.10).I would like to add Gabonator and Pawn but like other (most?) peoples the DFU mode doesn't works. I try on 2 computers with...
View ArticleCANBUS problem - no data received - led not blink
Hello,I'm interfacing to a one canbus of my car running at 125kBaud and am just using the sample read program with the speed changed to 125. I'm not getting data and the red led (rx) blink very...
View ArticleClik here to view.
Grove OLED Display 0.96" 128x64 on Arduino Micro...not works
Hi,I really need to use an Grove OLED Display 0.96" 128x64 on my ARDUINO MICRO, but it’s not working. The display works fine on the Arduino UNO.Then I try to make it works with my Arduino Micro.The...
View Articlerestore orignal app
I am going to answer my own question... Took me a while to find it, but there is a firmware upgrade wiki (duh). On that page was the PA1_V110.HEX firmware which has now restored my unit to working...
View Articlerestore orignal app
Hello, everyone.I bought a dso203 from amazon and it came as a 2.72 8M unit. Played around with it, loaded gabonator's app to slot 4, works great, so I thought I would try the community app. Things...
View Articlegprs shield sim900 firmware upgrade
HI,I have the GPRS shield V2 with sim900 module. How do i upgrade the Sim900 module since it is part of a shield?Any help is much appreciated.Richard.Statistics : Posted by r.yates • on Tue Jun 03,...
View Article
