Charging Arduino from solar battery
Which shield should I choose: Shield Energy Shield, Solar Charger Shield V2 or some other? What's the difference?Do they provide information about current level of the charge?Must be shield manually...
View Articlemeasuring water level in a waterbarrel
I would like to measure the waterlevel in a water barrel using several moisture sensors.Each sensor would be put on a different level in the barrel (empty, 1/3, 2/3, full).If possible the water level...
View ArticleLinkIt BAT/USB switch
What for this BAT/USB switch? To prevent discharge of battery by disconnecting it from consumers? (so act as power off switch)? If LinkIt works from battery (switch turned to BAT) and then I will...
View Articlemeasuring water level in a waterbarrel
It will be easier to measure the weight of the barrel, and calculate the water level from that.Statistics : Posted by steve.vancompernolle • on Fri Nov 14, 2014 6:19 am • Replies 1 • Views 18
View ArticleDifference between Arduino regular and Linkit arduino
I'm using an Arduino Uno with the NFC Shield V2.0 - SLD01097P, connected directly together using the header pins. I thought perhaps it was voltage related and tried with a 12v supply to the UNO but no...
View ArticleDifference between Arduino regular and Linkit arduino
i.guillaume wrote:Thx,saves me some diskspace and another link on the desktop.Maybe you should mention it in the instructions.Hi, Thanks for you suggestion, if you have any question about LinkIt ONE,...
View ArticleDifference between Arduino regular and Linkit arduino
Thx,saves me some diskspace and another link on the desktop.Maybe you should mention it in the instructions.Statistics : Posted by i.guillaume • on Tue Oct 14, 2014 5:58 am • Replies 4 • Views 643
View ArticleDifference between Arduino regular and Linkit arduino
i.guillaume wrote:Is the arduino IDE used by the Linkit board any different from the regular IDE?In other words, can we just "merge" the files and use one IDE to do all target boards?Hi, LinkIt ONE IDE...
View ArticleDifference between Arduino regular and Linkit arduino
Is the arduino IDE used by the Linkit board any different from the regular IDE?In other words, can we just "merge" the files and use one IDE to do all target boards?Statistics : Posted by i.guillaume •...
View ArticleEthernet shield constant reset status
I'm looking for a contact on the Seeed Studio Ethernet Shield to connect to Arduino Pin to reset the Ethernet Shield by software in the sketch !!Statistics : Posted by rmorrow • on Fri Sep 19, 2014...
View ArticleEthernet shield constant reset status
The same happen to me, with the Seeed Ethernet Shield V2.0 every time the power goes down i need to 'MANUALLY' reset the shield or the arduino, because if i do not the Seeed Ethernet Shield stay on...
View ArticleEthernet shield constant reset status
As for the LEDs, that is probably because you do not have two active CAN nodes, just one, which means that the protocol controller is trying to send that message and there is no other node to...
View ArticleEthernet shield constant reset status
This is new to me. I have three Ethernet shields: the Official Arduino R3 Ethernet Shield with PoE module populated, the Freetronics Ethernet Shield, and the Seeed Studio Ethernet Shield V1.1 I picked...
View ArticleEthernet shield constant reset status
Hi, recently picked up an ethernet shield for my Arduino Uno R3. However... anytime I plug in an ethernet cable, theunit immediately goes into reset (red light comes on.) The device does not show up as...
View ArticleClik here to view.
DSO Quad Bootloader corrupted
jpa wrote:I did a dump of the whole flash memory using a custom app (no hardware mod necessary). The binary file from 0x8000000 to 0x8040000 is attached.Good luck!Hi jpa,many thanks for your dump, you...
View ArticleDSO Quad Bootloader corrupted
I did a dump of the whole flash memory using a custom app (no hardware mod necessary). The binary file from 0x8000000 to 0x8040000 is attached.Good luck!Attachments dso_quad_bootloader_flash.zip Flash...
View ArticleClik here to view.
DSO Quad Bootloader corrupted
Hi all,working on some customization of the latest DSO Quad "SYS" and "APP" source codes something went wrong after the uploading of a HEX file to the DFU disk, because now my DFU Bootloader has been...
View ArticleDSO Quad Bootloader corrupted
Did you download the whole blob to your DSO or just the 16k boot loader?Statistics : Posted by embedded • on Wed Nov 09, 2011 4:48 am • Replies 15 • Views 5251
View ArticleACT05161P mounting enclosure?
Hi,Is there an enclosure (preferably sealed and transparent) that you guys sell that would align with the mounting holes on a grove ACT05161P? Does anyone know?Statistics : Posted by kris • on Mon Nov...
View ArticleClik here to view.
More configurations available ?
msmola wrote:I am using my new DSO Quad ( 2.81/1.62/1.13 ) with oficial firmware (I think). What could be best firmware for it ?Would you be able to download DFU for me please? I have "lost" mine and...
View Article
